glossary:glossary_b
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
glossary:glossary_b [2019/09/05 16:47] – [Bps] Changed Bytes to Bits tgerbic | glossary:glossary_b [2020/09/14 14:43] – [Block Control] grovenor | ||
---|---|---|---|
Line 6: | Line 6: | ||
- | Back EMF generally refers to the voltage that will appear across an inductor if the current is stopped suddenly | + | Back EMF generally refers |
[[: | [[: | ||
- | |||
===== Baud ===== | ===== Baud ===== | ||
- | Most people use baud to describe modem speeds in bits per second–but they are wrong. They may say a 9,600-bps modem transmits at 9,600 baud, but really | + | Baud in communications refers |
- | [[http:// | + | [[wp>Baud|Baud]] |
===== BC3 ===== | ===== BC3 ===== | ||
- | The BC3 is an automatic block control system otherwise known as SuperBloc (QV). It controls the speed of a model train depending on the occupation of the block ahead. If the block ahead is occupied the train will slow to a creep speed and stop at a designated point. Otherwise the train will accelerate to a preset speed. Manual control is also allowed for. Kits for the [[: | + | The BC3 is an automatic block control system otherwise known as SuperBloc (QV). It controls the speed of a model train depending on the occupation of the block ahead. If the block ahead is occupied the train will slow to a creep speed and stop at a designated point. Otherwise the train will accelerate to a preset speed. Manual control is also allowed for. Literature |
- | The BC3 kit is No38 Nos 39 and 40 are a test jig and a setting up kit. Kit instructions for 38 and 39 are available from MERG.\\ | + | although kits have been discontinued. |
- | [[https:// | + | [[: |
- | [[: | + | |
===== Bell signals ===== | ===== Bell signals ===== | ||
- | Bell Signals were used to convey information | + | Bell Signals are used as part of a block signalling protocol. |
- | [[http://www.signalbox.org/ | + | |
+ | The cadence of the Bell Signals were used to convey information. | ||
+ | |||
+ | Though there are some commonly used bell signals, different railways at different times have had their own signaling schemes. | ||
+ | \\ | ||
+ | [[https:// | ||
===== BGA ===== | ===== BGA ===== | ||
Line 58: | Line 60: | ||
- | Block control is the philosophy that a railway should be divided into blocks and that no train should normally be allowed to enter a block which is already occupied. This means that each block has a stop signal at which a train is required to wait if the block ahead is occupied. This will be set back 0.25 mile from the start of the next block. Further back there will be a distant signal which informs the driver that he needs to slow because the signal ahead is at stop.\\ | + | Block control is the philosophy that a railway should be divided into blocks and that no train should normally be allowed to enter a block which is already occupied. This means that each block has a stop signal at which a train is required to wait if the block ahead is occupied. Further back there will be a distant signal which informs the driver that he needs to slow because the signal ahead is at stop.\\ |
Modern electric signalling systems allow for more variation in slow signals with the a double yellow as a preliminary caution as well as the yellow caution to give two stages of slowing.\\ | Modern electric signalling systems allow for more variation in slow signals with the a double yellow as a preliminary caution as well as the yellow caution to give two stages of slowing.\\ | ||
[[http:// | [[http:// |
glossary/glossary_b.txt · Last modified: 2022/10/10 21:55 by Bob Vetterlein