Printed Circuit Board. Are usually made of Fibreglass or SRBP (Synthetic Resin Bonded Paper) with a copper laminate on one or both sides, forming the electrical circuit. A detailed Wikipedia article is available here. Most MERG Kits contain a PCB, the majority of them are single sided through hole construction. As the electronics become more sophisticated so double sided and surface mount technologies are being introduced.
Software for producing the “Gerber” files which are used in the etching process to produce the required PCB’s
The PECO implementation of the Point motor, notable because they are constructed so as to be directly attached to both N and 00 gauge PECO track, thus making it easier to line up the pull and throw of the point
Used for the printable surface on some 3D printers, especially the Prusa range
Peripheral Interface Controller. A complex integrated circuit which may be programmed to carry out a controlled sequence of events, ie certain output events controlled by an input event.
A brand of micro processor chip from Microchip, often used in MERG projects. Eg PIC18F2480.
A device marketed by Microchip for programming their PIC microcontrollers. Beware of imitations.
The pin out of the PICKit differs from that of the programming connector on MERG CBUS boards, see here for details of how to build a connecting lead. A useful pdf is available from the Picprijects website, detailing the pin out of various PIC packages.
Parallel in Serial out, refers to a type of Shift Register where data present on a set of input pins is captured by application of a strobe pulse and then presented on a single output pin under control of a clock. For a graphic description see Shift in/out.
Phase Modulation. A specialist modulation mainly used in Radar equipment, the phase rather than the frequency of the carrier wave is varied in order to obtain information
There are basically 3 forms of pulse modulation, Amplitude, Position, and width, each having its own characteristics and uses. This type of modulation may be superimposed onto RF or on DC voltages.
A piece of electronic kit designed by Gordon Hopkins which may be used to switch fast action point motors See TB G16/14
A piece of electronic kit designed by Gordon Hopkins which may be used to switch slow action point motors See TB G16/15
Solenoid Point motor /relay driver with on board relay see TBG16/26
Pocket Money Project. Excellent simple, basic and inexpensive kits to learn basic electronic theory and techniques such as soldering. Currently there are 23 Kits and most cost less than £2.00. You can find them in the Kit Locker here.
An electro mechanical device for switching points. There are many examples of point motors, some are fast solenoid switched and others slower acting motor switched
A track based device for manually or electrically switching one input track to two or more tracks, or two or more tracks into one track. Also called turnouts in NA.
Power ON reset i.e. just turning the power on to the whole system.
Abbreviation for Potentiometer see below
Power to the track is divided into sections. Can be to assist fault finding, to avoid shutting down the whole layout if a short occurs, and in large layouts to provide separate power supplies one to each district.
A controller including a power supply to the track.
The activity of entering a list of instructions that a computer can act on. That is “run” the programme. These instructions take the form of a programming language that the computer can understand.
The means to facilitate manually driven trains following one another on the same track but in different electrical sections powered by different controllers. (See MERG Journal Autumn 2005 page 10 (August 2005) and Winter 2005 (January 2006) page 10 )
Power supply unit
See also Dirty PSU
RPC System - PTP (Point-to-Point)
Self contained (non-PC) automatic data transfer system for up to 960 functions each way, using standard RPC Modules. Includes PCBs and all components.
Multiplex system using a RS485 bus, matching pairs of input and output modules communicate under the control of a master module.
For details see these TBs: LC02/01, LC02/02, LC02/03, LC02/04 & LC02/05.
Can be any shape and is normally a short period of time. A rapid change of voltage or signal for a short duration.
Pulse Width Modulation is a technique used to control devices such as motors and lights to vary the amount of power supplied to the device. The power supply to the device is switched between off and on such that the average power to the device can be varied between 0% - always off to 100% - always on. For example if the wave form is switched so that a motor is connected to power supply for 75% of the time then it will receive approximately 75% power and run at a slower speed. The frequency at which the switching takes place will affect the behaviour of the motor but is typically between 100Hz and 20KHz.